Skip to content

Fitting A New Car Battery.

Typical clues your car battery is about to give up are alternator problems, slow starting, electrical issues, lamps dimming,or already having had to jump your car.

Maybe you didn't observe or there were no signs of your car battery breaking down and you find yourself stranded at work, it may be worth finding a car battery replacement service in your area.

You may want to change the car battery on your own. The following is a general guide on how to replace it yourself. Before attempting to change Its suggested to look at the vehicle manufacturers guidance for your individual car.

If you have never replaced a car battery before, or your vehicle has particular needs like battery registration, you may be better to get car battery installation specialist to accomplish the task for you.

Things to consider is that most modern cars are very electrical dependent and store settings for electrical components,windows, roofs, and radios.

If you detach your battery without any an external power back up you may lose these configurations.

Cars installed with Stop/Start systems and some other modern vehicles that have particular charging systems that keep track of the power level coming from the alternator to battery, need brand-new batteries to be registered with the car.

These battery registration tools are expensive, and while you may be able to take the car to a nearby repair shop that has the hardware, they may well unwilling to register the new battery as they did not fit it.

In case your vehicle is equipped with the new AGM style battery it must be replaced with the exact same sort and not a traditional lead acid sort as this will occasionally create electronic issues and possible premature battery malfunction.

Verify you have the right automotive battery for your car prior to attempting to switch it out, most batteries have a sticker probably on the top or side that contains the battery amps, battery sort and battery cranking on it.

Battery Replacement Approach

Every thing Switched Off (First Step).

See to it that all of the your car electrics are switched off and keys are taken out from the ignition.

Locate the car battery (Second Step).

Depending on your car type the following are some of the most regular battery places, underneath the seats, bonnet, and in the boot area.

Take away battery hold downs (Third Step).

Your battery may probably have a bracket over the top or a small hold down at the base fixing the battery into place. These are normally held down with 8mm,10 mm, or 13mm bolts or nuts, a long socket and bar set could be called for.

Beware as cars age the hold downs can easily get corroded, which can consist of having to change the battery holder. (Apply some fast release substance on it if they look corroded).

Connect External Power (Fourth Step).

Hook up the battery memory saver to the car if vehicle electrical configurations have not already been lost as a result of a dead battery. Make sure you adhere to the tool producers information on the best way to do this.

Removing The Used Automotive Battery (Fifth Step).

When you disconnect the dead battery, if you have a battery memory saver hooked up the battery terminals are going to still be live.

When unfastened, you will have to make certain that the terminals do not enter into contact with another metal surface. Upon taking off endeavour to cover them using a non conductive item.

Most vehicle battery terminals use 8mm,10 mm,13 mm nuts these could generally be undone with a wrench.

Disconnecting the terminals.

(Negative Terminal 1st).

The primary terminal to remove will be the negative that has the - (minus) icon on it or the battery area itself.

(Positive Terminal 2nd).

Then remove the positive terminal that has the + (plus) icon on it or the battery itself.

Once you have the terminals detached transfer them out of the way so you have full access to extract the battery (make sure that not to make it possible for the detached terminals touch anything). A few vehicle batteries also have a gas venting out line connected, this should be detached before extraction.

Connecting the new automotive battery (Sixth Step).

See to it that the battery place is clear and clean, then verify the battery terminals are out of the way and place the automotive battery back into location.

(Connect the Positive Terminal 1st).

Take away the non-conductive protection from the positive battery terminal and attach to the positive terminal on the battery. Make sure it is secure and then re tighten.

(Connect the Negative Terminal 2nd).

Take away the non-conductive cover from the negative battery terminal and attach the negative terminal on the battery. Ensure to push it down and afterwards re tighten. In the event that you have a battery gas ventilation pipe reconnect to the new battery.

Remove the external power/battery memory saver (Seventh Step).

When you are happy that your new car battery is attached you may now remove the battery memory saver tool. (Do Turn On Or Start The Car With The Battery Memory Saver Still Hooked up).

Start the car (Eighth Step).

You may now start the car to verify everything is working, when you are happy the new battery is connected and the battery saver is removed.

Refit the battery hold downs (Ninth Step).

Once you have started the car and all is ok refit the battery brackets making sure you do not make connection with the battery terminals.

Stop/Start and Batteries Requiring Registration (Tenth Step).

Car batteries that involves battery registration you could now link the battery registration hardware and perform the process.